How To Repair Hole In Sole Of Shoe

Download Article

Soles are oftentimes the first part of a shoe to vesture out. Fortunately, as long as the rest of the shoe is in skillful shape, repairing the sole tin exist an piece of cake way to make your shoes proficient as new. With a lilliputian sandpaper and some shoe sole adhesive, you tin supersede worn-out soles or fix holes or loose soles in only a few minutes, and wearable them once again within 24 hours.

i
Pull the one-time sole off with pliers. Even if the sole is starting to come up loose, y'all volition probably demand pliers to pull information technology off the shoe entirely. Hold the shoe firmly and pull on the edge of the sole with pliers, moving the sole abroad from the bottom of the shoe. If the sole doesn't come off hands, try wedging a paint scraper or butterknife between the sole and the shoe as you pull on the sole with pliers.^[1]
- You can also utilize a heat gun or hair dryer to warm up the glue that attaches the sole, which volition arrive easier to remove.
ii

Clean off whatsoever old gum using acetone. There may yet exist some dried gum remnants on the bottom of your shoe where the sole was attached. Cascade a trivial acetone or nail polish remover on a rag and scrub the bottom of your shoe with it. The gum should dissolve and scrub off. Clean whatever dirt or residue grime off the shoe as well.^[2]

Advertisement
3

Roughen upwards the bottom of the shoe and the new sole with sandpaper. Rough surfaces hold together better with glue than polish ones. Employ 120-dust sandpaper to scratch up the bottom of the shoe and the superlative of the sole until their textures appear rougher.^[3]
4
Utilise shoe sole adhesive to the new sole with a brush or cotton brawl. Follow the instructions on the adhesive for application. Some adhesives must sit for a few minutes, or "cure," earlier the particular can exist put in place. Some adhesives require heat to be activated
- Shoe Goo is a common and effective shoe sole adhesive, and is available in many shoe shops, sports supply outlets, and section stores.
5

Put the new sole in place and press it tightly against the shoe. If the adhesive needs to cure earlier it's used, wait for every bit long as the instructions indicate earlier putting the sole on. Start at the forepart and lay the sole gradually on the shoe, making sure the edges line up properly. Once it's in place, apply pressure to stick it firmly on the lesser of the shoe.
half-dozen
Clamp the sole to the shoe using prophylactic bands, duct tape, or weights. The sole needs to be pressed tightly confronting the shoe for the ii surfaces to adhere. Secure the sole in place past wrapping safety bands or duct record effectually the shoe, or past placing it on the basis and setting weights on top of it to press the shoe into the sole.^[4]
- It can be helpful to stuff the shoe with newspaper first then that it keeps its shape while being clamped.
vii

Wait 24 hours before using the shoe again. Most shoe sole adhesives take at least a full 24-hour interval to prepare. Allow your shoe sit somewhere absurd and dry where it's non in danger of being moved or touched.^[5]

1

Clean the shoe and sole with water and booze. Employ a rag to rub some warm water and isopropyl alcohol over the surface area around the loose part of the sole. If you can exercise so without pulling it off further, clean inside where the sole has become loose also.
2
Use shoe sole adhesive between the shoe and the sole. Use a toothpick or cotton swab to utilize a layer of adhesive within where the sole has come apart from the shoe. Make the layer fairly thick, as it'due south improve to put in besides much and have information technology overflow than to not have enough.^[6]
- Some adhesives need to cure for a few minutes after existence practical and before the sole is put in identify. Cheque the instructions on your adhesive product.
3

Press the sole confronting the bottom of the shoe. Being careful not to become any agglutinative on your hands, printing the sole and the shoe together tightly. Don't worry if some adhesive spills out -- this tin be sanded off later.
4

Keep the sole in identify with safety bands, duct record, or weights. The sole should exist pressed tightly confronting the shoe for the unabridged time it dries. Secure information technology using rubber bands or duct tape, or set weights on pinnacle of the shoe in the expanse where the mucilage is drying.^[7]
5

Permit the shoe sit for 24 hours. Place the shoe somewhere out of the manner, where information technology can stay absurd and dry while it sets. Wait at least a full twenty-four hours earlier wearing the shoe.^[8]
6

Sand off any dried overflow glue. If whatever of the shoe sole agglutinative spilled out when you lot pressed the sole downward, sand it off using 120-grit sandpaper. Make sure the adhesive has dried out completely before sanding information technology.^[ix]

Advert

1

Clean the area around the hole with water and alcohol. Employ a rag to rub warm water and isopropyl booze around the hole to clean off any dirt or crud. Let information technology dry out for a few minutes before standing.
2

Roughen upwardly the edges of the hole with 120-grit sandpaper. This will help the glue adhere to the rubber. Scrub the edges of the hole with sandpaper until information technology appears to take on a rougher texture.^[ten]
3

Put duct tape over the within of the shoe above the hole. Remove the insole of the shoe and place a piece of duct tape inside the shoe where the hole is. If the pigsty does not become all the manner through the inside of the shoe, put your finger in the pigsty and push button up to come across where the hole is and cover that part with duct tape.^[xi]
4

Fill the hole with shoe sole adhesive. Existence careful not to affect the adhesive with your bare hands, gently squeeze it into the pigsty. Brand sure the entire hole is filled, and don't worry if there is some overflow.
five

Use an ice cube to polish the surface of the adhesive. The ice cube volition allow you to smooth the surface of the glue without sticking to information technology. Yous can also utilise a tongue depressor or spoon covered with petroleum jelly.^[12]
6

Let the shoe dry for 24 hours with the sole turned upwardly. Fix the shoe so that the sole is facing upward. Exit it somewhere out of the manner where it will be cool and dry. Go out it for at least a full day.
vii

Sand downwards whatever dried agglutinative that overflowed from the hole. Check to see if there is stale glue protruding from the hole or spilling out over the edges. If at that place is, use 120-grit sandpaper to sand it down until the bottom of the sole is smooth.^[13]

Add New Question

Question

What should I check earlier I repair or replace my soles?

Rio Jongsae Kim is a Designer Shoe and Bag Repair Specialist and the Owner of Kim'south Shoe & Bag Repair in Vancouver, BC, Canada. With over 40 years of experience, Rio and Kim'southward Shoe & Bag Repair specialize in the repair and reconstruction of leather and luxury appurtenances including shoes, handbags, and accessories. Rio's experience and dedication to quality repair and restoration accept led to his work being featured on Yahoo, Insider, and MSN.

Designer Shoe & Bag Care Specialist

Expert Answer

You have to check to meet if the soles accept started to thin, or they take holes. Yous should also cheque both shoes to see if they're wearing abroad evenly, or if they're splitting from the upper side of the shoes.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advert

To avoid getting adhesive on your pare, habiliment disposable gloves when applying the adhesive or handling the shoe afterwards you've glued it.

Nearly This Article

Article Summary X

If you demand to repair a shoe sole, commencement by cleaning all over the shoe with a mixture of warm h2o and isopropyl alcohol then the adhesive will stick. Once the shoe has stale, use a toothpick or cotton swab to apply a thick layer of agglutinative where the sole has come autonomously from the shoe. And then, press the sole confronting the bottom of the shoe tightly, making certain not to get any adhesive on your easily. Don't worry if the adhesive spills out of the cracks, you can e'er sand it off later. Since you want the shoe and sole pressed tightly together until the adhesive dries, secure them together with safety bands or tape. After waiting 24 hours, remove whatsoever safe bands or tape and sand off the overflow glue with 120-grit sandpaper. For more help, like how to fix a hole in the sole of your shoe, read on.

Did this summary assist you?

Thank you to all authors for creating a folio that has been read 171,085 times.